1】将下载的程序包下的lib文件夹，复制到Arduino IDE 库路径的libraries文件夹下(重要)

这些复制到Arduino

首选项选择arduino文件夹

2】配置Arduino IDE 的相关参数(重要)

烧录成功但黑屏， com13 反复发送：ELF file SHA256: 0fc790356841d2bf

Rebooting...
ESP-ROM:esp32s3-20210327
Build:Mar 27 2021
rst:0xc (RTC_SW_CPU_RST),boot:0x8 (SPI_FAST_FLASH_BOOT)
Saved PC:0x40377450
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fce3808,len:0x44c
load:0x403c9700,len:0xbe4
load:0x403cc700,len:0x2a68
entry 0x403c98d4
E (136) psram: PSRAM ID read error: 0x00ffffff, PSRAM chip not found or not supported, or wrong PSRAM line mode
Hello T-HMI
Guru Meditation Error: Core  0 panic'ed (InstrFetchProhibited). Exception was unhandled.

Core  0 register dump:
PC      : 0x00000000  PS      : 0x00060031  A0      : 0x82026d84  A1      : 0x3fcb8ca0  
A2      : 0x00000000  A3      : 0x3fcf4460  A4      : 0x00000020  A5      : 0x80000000  
A6      : 0x00060021  A7      : 0x00000001  A8      : 0x82006617  A9      : 0x3fcb8c80  
A10     : 0x00000000  A11     : 0x00000001  A12     : 0x00000000  A13     : 0x00000020  
A14     : 0x02cb9580  A15     : 0x00ffffff  SAR     : 0x00000002  EXCCAUSE: 0x00000014  
EXCVADDR: 0x00000000  LBEG    : 0x00000000  LEND    : 0x00000000  LCOUNT  : 0x00000000  

Backtrace: 0xfffffffd:0x3fcb8ca0 0x42026d81:0x3fcb8cc0 0x403752c5:0x3fcb8ce0 0x403752ea:0x3fcb8d00 0x40378851:0x3fcb8d20 0x420196da:0x3fcf46a0 0x4037c181:0x3fcf46c0 0x4037c24f:0x3fcf46e0

ELF file SHA256: 0fc790356841d2bf

多按几下复位按键试试，看看是不是复位失灵了

COM13  提示 2 个错误：

E (136) psram: PSRAM ID read error: 0x00ffffff, PSRAM chip not found or not supported, or wrong PSRAM line mode
Hello T-HMI
Guru Meditation Error: Core  0 panic'ed (InstrFetchProhibited). Exception was unhandled.

按照这样 重新烧录试一下

需要按照如下要求配置arduino，否则不能正常显示

按照以上配置之后。 剩下 1 个 error：

Guru Meditation Error: Core  0 panic'ed (InstrFetchProhibited). Exception was unhandled.
Core  0 register dump:
PC      : 0x00000000  PS      : 0x00060031  A0      : 0x82026cb8  A1      : 0x3fcb9310  
A2      : 0x00000000  A3      : 0x00ffffff  A4      : 0x6001f000  A5      : 0x00000001  
A6      : 0x3fcbc2d4  A7      : 0x00000000  A8      : 0x8200660f  A9      : 0x3fcb92f0  
A10     : 0x00000001  A11     : 0x00000001  A12     : 0x8037de0d  A13     : 0x3fcf4600  
A14     : 0x00060d23  A15     : 0x00000000  SAR     : 0x00000002  EXCCAUSE: 0x00000014  
EXCVADDR: 0x00000000  LBEG    : 0x00000000  LEND    : 0x00000000  LCOUNT  : 0x00000000  

1】确保板子型号选择正确

2】确保库选择正确

问题已解决

1】将下载的程序包下的lib文件夹，复制到Arduino IDE 库路径的libraries文件夹下

这一步没有操作导致的不显示